Gasoline Autool C100 injector Cleaner C100 Fuel System Throttle Valve Clean USer Manual

Gasoline Autool C100 injector Cleaner user manual. C100 Fuel System Throttle Valve Clean  include many different kinds of adapter, cover almost all the EU,Asia,USA cars and light trucks. Non-Dismantle injector Throttle and fuel system.

 Here list the Gasoline Autool C100 injector Cleaner C100 Fuel System Throttle Valve Clean USer Manual from cablesmall, pls kindly check it:

AUTOOL C100 Fuel Injector Cleaner C100 Non-dismantle Injector Tester

 

CFS Series Fuel System On-vehicle Cleaning Assistant

1

CFS Series

Fuel System On-vehicle

Cleaning Assistant

CFS Series Fuel System On-vehicle Cleaning Assistant

2

The operation procedure of fuel system cleaning:

Firstly, please check the car being with which kind of fuel system, carburetor system or

electronic fuel injection system.

Operation for the electronic fuel injection system as follows:

The pipeline connection of the engine:

Engine with fuel-return pipe

1-CFS Cleaner;2-Engine;3-Connecting the plug;4- The fuel-outlet pipe of the CFS;

5-Filter;6-Fuel-outlet pipe of engine;7- Fuel-return pipe of engine;8-Fuel pump;9-Fuel tank。

a) Disconnect the fuel-outlet pipe(C、D) and the fuel-return pipe(A、B) of the engine, and

select a suitable connector to separately connect the port B and port C to the plug and the

outlet pipe of CFS.

b) Connect the left two ports (A, D) by a suitable pipe. Or unplug the engine fuel pump fuse, or

disconnect the power cable of the engine fuel pump.

1- CFS Cleaner;2-Engine;3-Plug;4- The fuel-outlet pipe of the CFS;

5-Fuel tank;6-Filter;7- Fuel-outlet pipe of engine;8-Fuel pump;

a) Disconnect the fuel-outlet pipe(E、F) of the engine, and select a suitable connector to

connect the port E to the outlet pipe of the CFS.

b) Block the other port(F)(Warning: just when the fuel pump being with overflow port). Or

unplug the engine fuel pump fuse, or disconnect the power cable of the engine fuel pump.

The pictures:

Pour the mixture of gasoline and detergent into steel bottle of the CFS.

Close the valve of CFS’s fuel-outlet pipe and open the valve of CFS’s air-inlet port and then

connect to the compress air. Adjust the pressure of air within 0.3 to 0.4MPa(3 to 4kgf/cm2)

by air control valve.

Connect the fuel supply adaptor of CFS to fuel supply pipe of the car fuel system, and open

the ball valve. Check if it has some leaking between all the connections. There must have no

any leaking when doing the cleaning work.

Start engine to start flushing the fuel system.

Drain out the pressure in the CFS’s bottle after flushing, and then disconnect the CFS.

Restore all of the pipes of the fuel system and check there have no leaking.

The connection ways for carburetor fuel system is same to electronic fuel injection

Caution:

a) Wear protect gloves and cloth when operating.

b) Must stop engine if there have any fuel leak!

c)

Bind up the pipe as disconnect the pipe to avoid splash and fire.

d) Please prepare at least a fire extinguisher when doing on-vehicle cleaning.

e) Please lead the exhaust to outdoor when doing on-vehicle cleaning, because it contains a

variety of toxic and hazardous gases.

f)

Please put the transmission in N and pull the brake when doing on-vehicle cleaning.

CFS Series Fuel System On-vehicle Cleaning Assistant

4

The operating procedure of TWC and intake manifold flushing:

Pour the TWC detergent into the bottle. Open the Ball Valve and Air Pressure Regulating

Valve to keep the air pressure as zero.

Connect the TWC Flushing Kit to the output pipe of the CFS.

TWC Flushing Kit

Disconnect the Intake Vacuum Pipe which near the throttle and insert the TWC Flushing

Nozzle into Intake Vacuum Pipe as shown.

Start the engine, and open the Ball Valve slowly which be sure to make the detergent into

engine vacuum pipe very slowly. The flushing process needs about 30 or 40 minutes.

Keep the engine speed up to 1000 rpm and press the accelerator every 3~5 minutes to make

the engine speed up to 2000 ~ 3000 rpm and keep this state for 30 seconds. Then keep idle

Do the flushing procedures as above until to exhaust the detergent. Then stop engine and

reconnect the vacuum pipe.

Start engine as idle speed for about 5 to 10 minutes to exhaust the detergent in the pipe.

The operating procedure of Throttle body and exhaust pipe flushing:

Pour the Throttle Body detergent into the bottle, and close the Ball Valve of the fuel outlet pipe.

Ball Valve

Intake Vacuum Pipe

Air Pressure Regulating Valve

CFS Series Fuel System On-vehicle Cleaning Assistant

5

Open the ball valve of the air inlet port and connect to the compressed air. Adjust the air

pressure to about 0.5MPa(5kgf/cm2) and then close the Ball Valve of air inlet port.

Connect the spray nozzle kit to the fuel outlet port of the CFS.

Spray nozzle kit

Remove the pipe ahead of throttle before flushing as shown.

Put the spray nozzle kit in the throttle body as shown and start the engine. And then open the

Ball Valve of fuel outlet port .

Keep the engine speed up to 1000 rpm and press the accelerator every 3~5 minutes to make

the engine speed up to 2000 ~ 3000 rpm and keep this state for 30 seconds. Then keep idle

Do the flushing procedures as above until exhaust the detergent.

Reconnect the pipes and initialize the throttle.

Caution:

It must initialize the Throttle Position Sensor by automotive scan tool after

record a DTC.